Repairs to uPVC Windows

uPVC windows are a fantastic option for modern homes. They are long-lasting, durable and easy to maintain. In contrast to aluminium and timber, they don't rust or rot.

Cleaning and lubricating regularly UPVC windows and doors is essential. This will reduce unnecessary repair costs and increase energy efficiency.

1. Broken Glass

The broken glass in your windows could cause serious damage to your home and even be fatal. It is important to take the time to ensure that you're doing everything you can to ensure that your windows are in good condition.

For single pane windows, it can be relatively simple to replace windows, and the new one is usually able to fit into the old frame very easily. However, if windows with double panes are secured by internal beading, it'll be more difficult to get rid of the panes that are in place and replace them with new ones. In this case it is essential to buy plastic spacers to help the new pane fit into the window frame.

If you are going to try to remove the window panes yourself it is important to wear appropriate safety gear such as gloves that are thick and eye protection. It is also recommended to lay down a dropcloth prior to you begin working on the window panes to ensure that any shards of glass fall onto the fabric, not onto the floor, where they could be trampled.

It's a great idea tape the gap once the glass has been removed. This will stop drafts and water from getting into your home until a professional arrives to repair the window. It also acts as a barrier that will prevent any intruders from gaining entry to your home. If the gap is particularly large, you may want to consider using the security door with an integrated window as it offers the best of both worlds.

2. Sagging

Upvc windows and doors are a cost-effective, durable and energy-efficient alternative to timber windows with sash. In time, they could be affected by a variety of issues that include sagging. A window that isn't properly aligned can cause problems with light, draughts, and even security. If you find that your uPVC window is beginning to sag it's important to act quickly to prevent the problem from getting worse.

Repositioning the hinges can help fix a window that is sliding. To do this, you'll have to open the window so that you can access the frame. After that, using the screwdriver, you'll be able to remove the top and bottom hinges and adjust them by turning them clockwise or anti-clockwise. Once you've adjusted the hinges, shut your window and verify the an appropriate fit. If you're satisfied with the fit, you can tighten the screws until they stay in place.

If you can't reposition the hinges, you might need to replace the seal. Rubber seals may dry out and lose their elasticity over time, leading them to loose their elasticity. If this happens, it's crucial to replace the seal as fast as possible so that your uPVC windows are watertight and secure from draughts.

uPVC handles may also become loose. This is often caused by screws that have loosened over time, but it can also be due to the mechanism of the handle wearing out. It's relatively simple to fix a loose uPVC handle. First, you'll need close upvc repairs near me your window and do an initial test to ensure that it fits. The corners of the sash must align with the casing joint. If it does not then you can use the screwdriver to loosen the handle. Then turn the mechanism back into place.

3. Water Leaks

If you awake to wet floors and mouldy walls each time it rains, it's crucial to take action. Water leaks through windows can cause structural damage to your home, and affect your ability to regulate the temperature of your home. The most common reason for leaks in uPVC windows is that the sealant surrounding the frame is damaged or is missing.

This is a relatively easy fix that can be done by any competent DIYer. Depending on the severity of the problem the caulking that was used up may need to be removed before a new layer can be applied. It is crucial to remember that when it comes to uPVC window repairs you should not be tempted to apply too much caulk in order to make the area more difficult to clean and could reduce your energy efficiency.

Check that any drainage holes do not have debris in them, and also ensure that the sill pan is properly angled to drain away from the window. In more serious cases you may need to think about replacing the window.

Mold spots and rotted sills are other signs of water leakage. This is a fungus that thrives in damp conditions and can quickly spread throughout the house.

It is also important to note that if the leak is coming from between the glass of your double glazed windows it may be more likely to be a problem with the glass seal, rather than the frame or sliding. This can be easily fixed by an uPVC window specialist who will replace the glass seal and restore the full insulation properties of your windows.

4. Faulty Hinges

If your uPVC windows are stiff to open, or loose and blow open with a breeze, it may be the hinges that are at the fault. These are easily repaired by any skilled DIYer and are usually done within a few minutes.

Like any mechanical part hinges are prone to be damaged over time. It is an easy process, but it's easier to do when you have a person to help you hold the frame in place.

It is also important to ensure that the uPVC hinges are opened and closed in the correct direction. This can be done by checking for the arrows on each hinge, this indicates which way the window should be opened.

Faulty window hinges could be caused by improperly opening the window in a particular way or by poor installation at the factory. This can often be resolved by sending us a photo via our website and we will be more than happy to give you advice.

It is also essential to lubricate the hinges regularly. This can be done by applying a light engineering oil to the hinges. We recommend using a solvent-free lubricant such as 3-in-one Multi-Purpose Oil. Regular lubrication can make the window easier to open and close. It can also prevent corrosion and decrease the chance of sticking. The ideal time to do this at least once a year. WD40 or other solvent-based lubricants should not be used since they can damage your uPVC windows.

5. Draughts

Draughts can be caused by different factors. The hinges can also be misaligned due to wear, which can cause gaps between the frame and sash. If they are beyond repair, it might be required to realign them. The interlock, which is on the hinge side of the window and can be misaligned. Again, it may be feasible to give them a clean but in some cases it might be necessary to have them replaced.

The second most frequent reason for draughts is window seals. They are susceptible to being worn out or damaged over time and let air escape through these gaps. Installing high-quality weatherstripping is a good way to stop draughts. Replace the windows made of Upvc with low-emissivity lenses. This will help to regulate indoor temperatures, and reduce the possibility of draughts.

One of the most effective ways to cut down on drafts is to use a draught excluder. These are typically made of fabric which are filled with a sort of filler and can be placed on the top of your windowsill. These will help to keep cold air out and keep your home warm and cozy!

Your windows made of upvc will continue to provide excellent insulation and security for your home by performing regular maintenance and repairs. It is crucial to keep in mind that all windows eventually get worn out and it may be cheaper to replace them instead of fixing them. So, if you are having issues with your upvc windows, it is always recommended to seek help from a professional as soon as you can.